1 Tph Boiler Makers

Side using fast excellent ultra-thin insulation effect as cotton glass furnace insulation materials, before and after the smoke box of the aluminum plates as a selected temperature insulation material; and the whole was sealed 1 tph boiler makers structure, no air leakage, the weld phenomenon is not tight, boiler to reduce heat loss to a great extent.

Fast 1 tph boiler makers in gas boiler industry has been at the leading level for low nitrogen environmental aspects of deep research. Dingzhou Yili Dairy determined after reaching cooperation with our company, launched a work plan for the boiler low-nitrogen transformation. Yili Dairy Dingzhou three original boiler 15t / h gas steam boiler, NOx emissions have reached 150mg / Nm3, belonging to the boiler equipment far exceeded. After the party fast professional and technical engineers, boiler and boiler model parameters to fully understand the components, rapidly developed a specific rehabilitation programs, start from the combustion system to achieve NOx emissions of 30mg / Nm3 to meet the most stringent environmental standards of the atmosphere.

As the industrial gas 1 tph boiler makers with a certain degree of risk in use, in order to avoid boiler accident hazards personal and property safety, boiler operators and maintenance personnel must pay attention to these guidelines in their daily work in order to better prevent accidents . Then the operation of industrial gas boiler should pay attention to what safety precautions it? Fast boiler tell you!

1, industrial gas boiler before use, it should be noted that check valve and out of the gas meter and the total furnace valve, and the pipe to be replaced when it is closed. When the door opened, they should pay attention to check the condition of the furnace, in particular, should pay attention to whether the occurrence of the phenomenon of gas leakage; if there is a leak, you can not fire, but to promptly check the repair to ensure the safety before ignition.

2, pay attention to check the flue gas of industrial boilers, water can not exist within the flue, and let the flue always remain open. Around the boiler does not allow stacking diesel, firecrackers and other inflammable and explosive materials, but also to set aside enough area of ​​safe passage.

3, before the industrial gas furnace ignition pot, should start before the blower, and the air valve to open the mouth of each combustion purged. We must pay attention to the fire ignition, such as gas, not upside down to prevent an explosion. Also note that when the burner ignited, should follow the order from top to bottom and from the inside and outside, in order to ignite and adjust.

4, in the use of industrial gas-fired boiler, because the power failure, etc. if the sudden stop caused by the blower, all need to immediately close the mouth of the combustion gas valve and air valves, and open the door in time to prevent an accident when necessary.

5, the operating room should be equipped with combustible gas, if gas leak discovered the phenomenon of indoor gas main valve should be closed, and then locate the leakage point and timely repair, care must be leak can not use an open flame during this process.

How to save electricity when using electric 1 tph boiler makersFirst of all, we first find out the power consumption of electric boilers, the main reason is poor insulation performance and improper use. As a result of improper use, the electricity bill will of course be increased a lot. So how should we save electricity? 1, your building indoor height. 2, indoor heating temperature. 3, the direction and number of floors of the room. 4, outdoor temperature. 5, adjacent to the living room heating. 6, Indoor doors and windows insulation effect. 7, the wall insulation conditions. 8, user methods and so on. Then the power configuration of the electric boiler should be reasonable. The power configuration is too big or small, but the power configuration is too large instead No power configuration, more tips. Power configuration is too small, the electric boiler has been working to achieve the set temperature, but also can not reach the set temperature. This is because the electric boiler fills the room with less heat than the room heat loss, the room heating is slow and not obvious, not only waste electricity, but also can not play a comfortable heating effect. People run at low temperatures when they are away. The electric boiler system has thermal inertia, can not be heated up immediately when it is opened, and can not be cooled immediately when it is closed. When you are away from home, turn down the temperature instead of shutting down the system, or shut down the boiler when you are away for a long time. Reasonable utilization of peak and valley electricity. Use of nocturnal valley electricity, with a slight temperature Fine-tuning, can even use a heat storage tank, peak electricity during the day, the temperature down. The house should be well insulated. Good thermal insulation can prevent excessive heat loss, doors and windows can not have obvious gaps, windows had better add double-layer central control glass, wall insulation, energy-saving effect will be very remarkable.